AAK hydraulic flow control valves were still normal after being used for 15 months near the sea, whi
Miguel is from a hydraulic equipment company in Brazil. He began to purchase hydraulic components in China 3 years ago, and it was successful. At the beginning of last year, the hydraulic flow control valves he purchased encountered problem and almost suffered a claim. Since using AAK hydraulic flow control valves to replace, he knows that there are also hydraulic valve manufacturers in China that have benchmarked the quality of German manufacturers.
Miguel company sold a hydraulic unit, which was used in wind power generation equipment near the sea. Half a year later, the customer complained that the valve body of the hydraulic flow control valve was seriously corroded and stuck, leading to the strike of the wind turbine generator. According to the factory feedback of the original hydraulic flow control valves, the corrosion of the valve body is caused by the objective marine climate, the hydraulic flow control valves can only be replaced. Miguel realized that replacing it within 6 months was not only expensive for after-sales, but also not necessarily acceptable to the customer. He purchased the hydraulic flow control valves from Germany to replace it. At the same time, he asked some new hydraulic valve manufacturers to make samples and required that the hydraulic flow control valves to be guaranteed for 12 months or more in the corrosive environment near the sea. Most manufacturers gave up, and only two were willing to test samples, including AAK.
After 40 days, AAK shipped the trial order of 30 hydraulic flow control valves. There has been no email from Miguel since the trial order was delivered. 15 months later, that is, last week, Miguel suddenly emailed us to purchase 800 hydraulic flow control valves. After communication, we learned that they were very satisfied with AAK hydraulic flow control valve samples delivered 1 year ago. The samples from another factory were corroded in 10 months, while AAK’s were still fine after 15 months. This service life was benchmarked to the hydraulic flow control valves purchased from German manufacturers, but the price of AAK was 30% cheaper, so they directly placed a big order.
AAK hydraulic flow control valves can be used in highly corrosive marine environment for 15 months without damage. The key lies in 3 points, which most domestic hydraulic valve manufacturers cannot do:
In terms of material, 3Cr3Mo3W2V hot working die steel is selected for the valve body, and its mechanical stress is optimized by at least 50% compared with other steels. After personalized heat treatment, the hardness, strength and corrosion resistance of the material are more than doubled.
In terms of surface treatment, zinc nickel alloy coating is adopted, and the corrosion resistance of the valve body is improved again. Its corrosion resistance is more than 10 times higher than that of ordinary zinc plating and nickel plating processes, which can ensure that there is no red rust after neutral salt spray test for more than 1500 hours.
In terms of detection, AAK has SH-90 salt spray testing machine, which tests the valve body according to the GB/T2423.17 test standard to ensure that any surface of the valve body meets the salt spray test standard.
AAK hydraulic flow control valves are safe to use near the sea, and durable under high pressure and high frequency use. You can also have a small try!
AAK HYDRAULIC CARTRIDGE VALVES (302) 2022-07-29
AAK replaced Italian manufacturer for hydraulic flow control valves used in aviation
At the beginning of this year, Hedwig sent an email asking for an ultra-high precision hydraulic flow control valve, with drawings and working conditions attached. Hedwig comes from an Italian hydraul3drops/min hydraulic flow control valve, AAK got back the reorder at a high price
Margaret, from India, is an old hand in the procurement of hydraulic components, especially good at price reduction, and has little cooperation with AAK, basically small quantities of high requirementThe surface roughness of AAK hydraulic directional control valves with mirror grinding is 12 times b
Fabian from the Netherlands left a message on AAK website last month: what is the reason for the hydraulic direction control valves stuck? In general, the processing roughness of valve spool and valveThe lifetime of AAK hydraulic flow control valve is twice as long as that of the peer, and AAK finis
At the end of last year, Stefan from Italy sent an email asking whether 50 non-standard hydraulic flow control valves could be produced within 25 days? For urgent orders like this, there is probably aTo lose a large amount of money in the Hydraulic Flow Control Valve, AAK used a small amount of mone
Bernardo comes from a hydraulic winch manufacturer in Brazil, and has cooperated with AAK several times on non-standard customized hydraulic cartridge valves. At the beginning of last year, Bernard coИнформация по AAK hydraulic flow control valves were still normal after being used for 15 months near the sea, whi предоставлена компанией-поставщиком AAK INDUSTRY CO., LTD. Для того, чтобы получить дополнительную информацию, узнать актуальную цену или условия постаки, нажмите ссылку «Отправить сообщение».